Spring seals factory in China: The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart. Find even more information at spring seals.
At the heart of why a mechanical seal works lies the rotating and stationary seal faces. Seal faces are lapped so flat it is impossible for a liquid or gas to flow through them. This allows for a shaft to spin, while a seal is being maintained mechanically. What determines the amount of time a seal will last is selecting the right seal material combination for the application. Hard seal faces for abrasive service, Carbon Vs. Ceramic for simple water (or anti-freeze in the case of automotive applications). Carbon Vs. Silicon Carbide for most applications to reduce energy consumption and provide long life. For critical applications double mechanical seals are usually recommended.
However, hydraulic transmission also has disadvantages compared with mechanical transmission: It is easy to leak and not friendly to the environment. High manufacturing precision is required. Low efficiency. The transmission ratio is not fixed. Due to the special working environment of construction machinery, its hydraulic system has the following characteristics: The working hours are irregular, and sometimes work continuously for a long time. The working environment is outdoors, the working temperature difference is large, and the working environment is dusty. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small. Due to the volume and weight, the working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa.
The O-ring of DMS SEALS is often used in hydraulic and pneumatic transmission systems and has wide applications. It can be used for both static and reciprocating seals. Moreover, it can also be used in rotary sealing systems. The O-ring can be installed in a groove with a rectangular cross section on the outer or inner circle, achieving a good sealing effect. It has many advantages compared with other types of sealing rings. Its compact structure makes it easy to assemble and disassemble. Moreover, its dynamic frictional resistance is relatively small, and a single piece of O-ring can achieve sealing performance in both directions.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Since the scraper seal is made of the special material, PTFE, it has an impurity immersion function. Therefore, when combined with the piston rod seal and the metal bushing, it can prevent damage to the piston rod and prevent the accumulation of oil pressure. It has a diameter range of 3-1600mm and a temperature range of -30°C + 200°C. The wiper scraper seal can operate at speeds of up to 5 m/s. It has high wear resistance, tear resistance, low-temperature resistance and good strength. Our wiper seals can be used in combination with piston seals and anti-wear rings to prevent oil in the cylinder from being mixed with foreign matter, which causes damage to the working seal. It is especially suitable for piston rods with a large diameter. Moreover, it has a wide range of applications, such as agricultural machinery, injection moulding machines, forklifts, cranes and so on.
Leakage of gaskets: There are four types of leakage phenomenon in general gaskets: interface leakage, penetration leakage, diffusion leakage, and damage leakage. Interface leaks: The interface will leak at the sealing interface due to insufficient gasket compression, improper flange joint surface finish, and flange deformation. For interface leakage, it can be prevented by using soft gasket to clamp in the flange face. Penetration leakage: Since most of the soft materials are made of fibers, they are easily soaked by the medium, especially the pressure. Due to capillary phenomenon, the medium will permeate to the low pressure side, forming permeation.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Find even more information at https://www.dmsseals.com/.
DMS Seals is a professional mechanical seals manufacturer and oil seal supplier for hydraulic seals, O-Rings, spring energized seals, oil seals, mechanical seal and so on. Hydraulic seals including step seals, glyd rings, guide strips, wiper seals, rod seals, piston seals, rotary seals, wear rings. We can provide the hydraulic seals with bronze filled PTFE, carbon filled PTFE, graphite filled PTFE, MoS2 filled PTFE, glass filled PTFE, virgin PTFE. About O-Rings, we can supply NBR, FKM, silicone, EPDM, HNBR, ACM, FFKM material.